- Can you sweat a pipe with water in it?
- Is it hard to sweat copper pipes?
- Can you overheat copper pipe when soldering?
- Can you Unsolder a copper pipe?
- What does NOM sweat mean?
- How reliable are compression fittings?
- Why are my PVC pipes sweating?
- What is a sweat coupling?
- How do you stop PVC pipe from sweating?
- Are sweating pipes bad?
- Does pipe insulation stop condensation?
- What is sweating in soldering?
Can you sweat a pipe with water in it?
Don’t try to solder pipes with water in them.
Soldering a joint in pipes that contain even tiny amounts of water is nearly impossible.
Most of the heat from the torch goes into turning the water to steam, so the copper won’t get hot enough to melt the solder.
Stop the trickle of water with a pipe plug..
Is it hard to sweat copper pipes?
Get perfect, leak-free plumbing joints every time. Soldering copper water supply lines is not a difficult skill. Even a rookie can learn to solder leak-proof joints in 30 minutes. The process is simple—if you follow a few basic guidelines. In this story we’ll show you how to solder copper quickly and easily.
Can you overheat copper pipe when soldering?
Overheating is a major problem when brazing or soldering copper pipe because the flux will burn (become oxidized), stop working, and become a barrier to tinning. In addition, a heavy oxide can be formed on the pipe itself, preventing a bond from forming between the filler metal and the pipe surface.
Can you Unsolder a copper pipe?
Unsoldering the copper joint can be done by applying high heat over the copper coupling or connection that needs to be detached. This process takes several steps to finish. First, you need to have the necessary tools to get the work done easily and accurately.
What does NOM sweat mean?
Nominal sweat inlet x 3/8 in. O.D. Compression outlet multi-turn angle valve with 5 in. Sweat extension tube controls water flow to household plumbing fixtures – faucets, toilets, dishwashers, icemakers, washing machines, etc. The angle valve is most often used where the water pipe enters the room from the wall.
How reliable are compression fittings?
Although compression fittings are generally considered more reliable than threaded fittings, there are some potential problems. In general, compression fittings are not as resistant to vibration as soldered or welded fittings. Repeated bending may cause the ferrule to lose its grip on the tube.
Why are my PVC pipes sweating?
The water on the outside of a sweating pipe is actually condensation. … When your cold water supply pipes are exposed to the warm and somewhat humid air of your home, moisture will form which can sometimes become excessive.
What is a sweat coupling?
Sweat fittings have a nonthreaded joint with a diameter slightly larger than the pipe. They slip onto the pipe, then when hot solder is applied, the solder seeps into the gap and fuses the fitting to the pipe. Compression fittings, on the other hand, have a threaded end with an attached nut.
How do you stop PVC pipe from sweating?
Seal joints between lengths of tubing with special “peel-and-stick” seam-sealing tape or foil duct tape. If your cold water pipes are sweating more than you are on these hot summer days, here’s the simple cure. Run down to the local home center, lumberyard or hardware store and pick up some foam pipe insulation.
Are sweating pipes bad?
Sweating pipes are not a serious problem, except for the fact that they create potentially dangerous moisture levels in your home. This can lead to mold and mildew issues or damage to drywall and framing.
Does pipe insulation stop condensation?
We can prevent condensation from occurring by insulating the pipe with enough insulation to keep the air around the pipe from dropping below the dew point. … It depends on the dew point of the air, which fluctuates according to the ambient temperature and the relative humidity.
What is sweating in soldering?
What is Sweat Soldering? Sweat soldering jewellery is a two part process whereby solder is melted onto one surface, cleaned, positioned and re-heated to join a second surface. As the metal reaches temperature, the solder floods or ‘sweats’ between the layers of metal, forming a strong and neat bond with no excess.